chipboard

What is the best way to lay tiles on chipboard flooring in a bathroom?

Replacing the tired old chipboard T&G sub in my galley kitchen and sistering a joist or two to level. Are chipboard T&G joints always glued these days? Polyurethane or a wipe of Gorilla? Thank you. Dain

I've been trying to get my 22m chipboard floor (on joists) flat in two rooms and a hallway of the 1st floor, so I can lay a floating click engineered floor. There is one high spot left in the hallway , which is partially over a steel I-beam which i think is why board is bent out of shape. I...

I am looking for some advice on suitable bathroom subfloors on joists. I have had a look on the forum, and am struggling to find an answer. Currently the bathroom subfloor is some kind of 18mm chipboard screwed onto the joists (400mm centres). Previously carpet was laid on top of this so...

Hi all I recently moved in to a new house. Before laying carpets i tried very hard to stop the chipboard flooring from creacking when you walk over it. Itspretty load everywhere! First I pulled up all the nails (long process) and replace with flooring screws, this stopped some of the really...

My builder wants to install chipboards on the loft conversion to have a solid working platform before plumber first fix. My question is how the plumber will be able to run the pipe through the joist without removing the chipboard? Does not sound ideal for me as the plumber will need to bring...

So i had to cut a few hatches in my tongue and groove chipboard flooring, for my new kitchen for plumbers and electricians to get access. However when avoiding the nails there are some that dont rest on the joist. Is it ok to "daughter" the joist to support the new hatches? TIA

As per attached photos. I have to close out my first floor and got some old flooring plank missing. As the 140x18mm are very difficult to find, can I used chipboard instead and cut to size. Is the chipboard strong enough where I have 20mm base support on the half joist? Thanks

Part converting garage to 2.4m x 2.4m utility. Have levelled concrete floor, 1200dpm, fitted 100mm then 50mm (90 degrees) solid insulation. Vapour barrier then tongue and groove 18mm MR chipboard, glued. Was quite pleased. Have recently read on some insulation websites that there should be...

I have recently started refurbishing my 2 bathrooms and have came to tiling part of my plan. In bathroom 1 I have screwed any loose floorboards to the joists so that there is minimal movement, and then I have put 2 layers of 9mm Ply Hardwood down with staggered joints and a layer of Wood Glue...

Hi, I am laying a new laminate floor in one of the bedrooms and have just lifted the old carpet and had my first look of the tongue and groove flooring. Some of the tongue and groove joints are very loose and when walked on sag and cause the floor to creak slightly - in the extreme cases the...

1st floor galley kitchen job (3m x 2m): I want to put click vinyl down but don't want the click to raise the finished floor level so I figure on replacing the 18mm chipboard sub with 12mm ply? Any thoughts? Do I need additional floor support perp to joists? At what ctrs? What size additional...

Ive just moved into a 12 year old home. It has roughly 200mm of insulation (2 sheets of 100mm), but suffers from the "modern house syndrome" of only having 38x75mm joists. This means my insulation sits very proud. I'm looking to board it out. Now, conscious that the existing joists aren't the...

Hi, New here. We are having a loft conversion done and company has failed time and again to waterproof the roof, so we are now experiencing the 4th rain leak in 5 weeks. As a result, one of the chipboard roof panels (where it leaked every single time) has been soaked through and through, and...

Sorry, this is a nested question.. Old suspended 1960s floor comprises: 3" void, 3" timber heights (sat on engineering bricks, levelled with cement), floorboards. Joist spacing sees 440mm approx inbetween joists. Joists are 2.5" wide. Goals: - insulate between timbers - UFH: install over tray...

We have just had a old gravity system removed and a new system boiler installed, the unvented cylinder has been placed in the loft. The loft is boarded with chipboard and the cylinder is sat in the middle of two joists with a wall running underneath. Is this safe?

Hi, As above, I've got a few sections of chipboard flooring that could do with being replaced before we get our new laminate flooring put down. Got the calipers out and it seems as though my T&G chipboard floor boards are 26mm deep. Most places only supply 18/22mm thicknesses (have found 26mm...

I know this gets asked a lot but I couldn't find a thread discussing the exact points I'm confused about. I'm refurbing a small (1.4 x 2.4m) shower room. The fitter has proposed the following for the subfloor: - 18mm moisture resistant chipboard screwed to the joists at 250mm centres, with...

I really hope someone can help, I'm slowly going crazy!.. We've got 170m2 of under flooring heating to fit upstairs in our new build but can't figure out the 'best' & cheapest way. Metal web/easi joists with 22mm chipboard. Planning to use 150mm mineral wool between joists. Majority of...

Hi all, Long time lurker, but I've generally been able to find everything I need already mentioned somewhere else...until now! I'm currently boarding out a small area in my loft around the hatch, and plan to do this straight on top of the joists. (The remaining area already has a raised floor...