shower tray

The waste hole for my shower tray is located in the middle, but the existing waste pipe is not aligned with it. Should I route the waste pipe under the floor to match the position of the waste hole, or is it possible to reroute it above the floor, given that the tray will be installed on a...

Hi. I am looking to bed an acrylic shower tray with a foam base on floorboards with 5mm plywood on top. Per manual, I will need a mix of sand and cement so I would like to know if anyone has some recommendations for a ready mix? I am wondering if the Blue Circle Quality assured Mortar or the...

I am currently doing a bathroom renovation and decided on fitting a Merlyn Level 25 stone resin shower tray. In the instructions, the first thing they get you to do is check that there isn't an excessive bow on all four sides. They do this by getting you to prop up the tray on four blocks of...

Hi, I have just poured some Mapei Ultraplan 3240 self leveller down to level the floor prior to fitting a shower tray. It says that it is walkable after 4-5 hours, does that mean I can install the shower tray after 4-5 hours or do I have to wait for the leveller fully cure first? Thank you!

I'm looking to install a Mira Flight Low Quadrant Shower Tray 800mm x 800mm x 40mm. My bathroom currently has 20/22mm chipboard flooring. I'm looking to fit the shower tray and tile the remainder of the floor. My plan is to overboard the chipboard flooring with either 6mm No more ply/ Hardie...

I'm looking for a new shower tray, but unfortunately I'm having to be quite specific with drain location due to the way my joists line up. I spotted this one from April Products, which would be ideal in terms of waste placement and overall size (1500x900mm). I notice Aquadart do an identical...

So, I've (hopefully) just about finished the plumbing in my bathroom renovation and it's almost time to reinstall the floor. I understand that when tiling, best practice is to tile the entire area and then locate the shower tray on top of the tiles, but what is the best solution for vinyl click...

Hello all, In the process of fitting a shower door onto a square raised shower tray for an alcove shower and would like some advice please. The shower tray has been sealed with silicone on the 3 sides already. When putting the shower door jamb to the wall and resting it onto the surface of...

I have received a stone resin shower tray and as best as I can measure, one corner is 3 mm lower than the other three (across the top of the tray edge) and I don’t know whether this is an issue or not? Are these things normally completely flat, or is it the norm that they are out of flatness by...

Recently been looking at buying a new shower tray, but note that most now have a smooth surface to stand on whereas my previous tray was rippled. My question relates to people’s experiences of these modern trays, in particular with regard to whether they are found to be dangerously slippy, or...

Sorry, newbie here. If this should have been posted in the Electrics or Flooring section please feel free to move. The previous owners installed electric underfloor heating in our ground floor bathroom, we cannot live without it as our only other heating in our home is the log burner but the...

Just fitted a large and heavy stone shower tray onto a mortar bed. I forgot to run silicon sealant around the edges, before tanking with liquid latex and adhesive repair tape from Aquaseal. The tape overlaps onto the shower tray, making a waterproof seal all around it. Do I now need to cut the...

Hi Guys, Just looking for some advice on fitting new shower tray. One wall is plastered, the other tileboard on studs. The tray edges are slightly tapered towards the bottom meaning the top is slightly away from the wall. I have cut away the plaster and board to allow the tray to sit somewhat...

I'm about to install a shower tray in a corner of my bathroom and would welcome any tips and answers to a couple of questions. I'm replacing some uneven floorboards with 22mm P5 chipboard flooring and I'm going to buy a Mira Flight tray 1000mm x 800mm and a bifold door with side panel. The...

Hi all, So got a 1000 x 800 concrete/acrylic shower tray to be installed straight onto 22mm moisture resistant chipboard floorboards (not using marine ply). I’ve actually used FBall P131 as a barrier/sealer. I put it on a 5:1 bed of mortar, but it failed me (came back following day and it just...

I have been quoted for a new plumbing system with 2 option. Worcester and ATAG boiler system. What your thought about these 2 brands? As I have also buy all the bathroom components including shower mixer, taps and ceramic. I know this is very objective in terms of design but what would a good...

Hi I've got a leak from a shower waste so I'm going to have to take out a section of the ceiling below (oh joy) to repair. Given the location of the water mark on the ceiling below, I'm reasonably sure that the leak is coming from the trap. The trap in question is one like this type...

Hello. I had a new shower put in last summer and it has never drained properly. It has a shallow tray and overflows easily due to the very slow rate of drainage. I know this is a common problem but none of the usual culprits seem to be causing it. Here are the facts : There was no drainage...

Hi I've got a stone resin shower tray like the one in the link below: https://www.amazon.co.uk/Rectangular-1200x900mm-Stone-Shower-Enclosure/dp/B005AFVYSW/ref=sr_1_5?keywords=shower+tray+1200+x+900&qid=1556089283&refinements=p_89%3AiBathUK&rnid=1632651031&s=gateway&sr=8-5 Its got a chip in the...

Resin shower tray has started to delaminate, wanted to rip it out and replace with pebble mosaics but the stud wall has been built on top of the edges so can't remove it without a lot of damage to the existing wall tiles (which are fine). Plan A Cut around the edge to remove the white plastic...