texecom alarm

I’ve recently installed a premier elite 24 system and upon entry to the property there is no entry tone and the alarm won’t sound. I get an exit tone, and when entering it says Area A arm etc but there is no sound on entry. I have no door contacts and have the PIR on the entry hallway as...

I have recently aqquired a Texecom Premier Elite alarm system for my house and I have installed it myself and so far its been ok as someone who has done lots of research, carefully read manuals and has an interest in alarms (please note this is a self install/DIY system) I also have a Texecom...

Hello I was wondering how to link out a zone on a Texecom Veritas R8 i was wondering also what could I use to link the zone out Many thanks Thomas

I’ve a Veritas R8 panel with the unset light flashing. Not a duplicate thread as: I checked battery output as was dead Checked fuse … ok Replaced battery … fault persists Closed panel and enter code + reset 2x … fault persists I’m now not convinced the panel is recharging the battery when...

Hi everyone. I have had a Veritas Excel for around 8 months now. Ever since installation it has been nothing but trouble. It's not the installers fault, just the system. Alot of the time to begin with in the evenings it would trip randomly and on the event log would state RKP OFFLINE and a...

I have a Texecom Premier Elite and SmartCom alarm system. I keep getting issues with access via the app failing, and the alarm installers haven't been super helpful, so I thought I'd see if I could get some clues here. The SmartCom (CEL-0001, Hardware Revision 26 if that helps) is connected to...

Hi sorry for a longer post, just trying to give as much detail as possible. I have recently moved into a house with a Texecom Elite 48 alarm ('menu - 4' shows sw v5.01.02.LS1) with a smartcom module installed. Over the past week or so I have been investigating the configuration of the alarm...

Hi all, I’ve just installed a texecom 64W Live, (main panel is in the garage) and wireless keypads have been fitted in the main house and out house. I’m struggling with the signal from the outhouse which is about approx 15-20meters from the main house. Is there any specific signalling booster or...

Hi Been pulling my hairs out over this. Got a new self install system (elite 64w with smartcom, 1 wired keypad and 1 wireless keypad) and everything is almost working perfectly, exepct for one thing - I cannot disarm from either keypad (wired or wireless). I am however able to disarm by keying...

Hello, Quick question for my texecom premier elite. I'm sure people will know the answer straight away. After getting the batteries replaced my part arm doesn't seem to be working as it did before. The back door works fine, when part arm is on and the back door is opened the alarms sounds...

My wifi provider was changed, so I am trying to connect my Smartcom to the new Wifi Connection so that I can reconnect my app. However, I am getting a “no internet connection” message (as seen on the screenshot below) when I’m trying to connect to Smartcom. I am unable to connect to the...

Hi There, I have a Texecom panel currently used for my home alarm. Everything is working great except that I wired up my electric fence energizer as an additional zone. Basically connected the energizer positive and negative to a normally closed 12v relay board and wired the zone as follows...

Hello All, Have been a lurker on this forum since I bought the premier elite alarm panel and have had some useful insights along with the texecom manuals. I have managed to setup all the zones and areas on the alarm and have successfully fitted the sensors , panel (5.04.02 Version) and a smart...

I have suddenly started getting a tamper issue with my Premier Elite Micro Shock Wireless sensor. I have checked the device and the cover is on fine however it will randomly trigger the sensor alarm. Does anyone know why this might be? Resetting the tamper fault will fix it for a couple of...

Hello, I have a Texecom Elite 64W with a Smartcom, I have internal sounders connected to the panel outputs. When the alarm is triggered and I attempt to disarm from the Connect App the external bell will stop but the internal sounders do not. The app says the system is "Disarmed" but the panel...

Hi Everyone Looking for some advice on my alarm setup (I don't have all the history of the install since it was done by the previous owners)... 1. In engineer mode, when I hit 'yes' on the 'YES to select Learn Ricochet' it immediately says 'All Devices Learnt!' but when I select the reset...

Hi all.. I recently bought a Texecom Premier Elite 64W. I have 4 core cabling in certain areas throughout the house for the pir sensors and then various other places such as the garage but since have had an outbuilding built and new doors which i wanted to add some wireless detectors to hence...

Hey, I have the Elite 64 Panel with a siren outside which I believe is the Odyssey X. I've just been alerted that it's on low battery. I thought it would be a simple job of just replacing the AA batteries inside, but having read the manual it seems not. It seems I have to; Activate the strobe...

Hi, I have a Texecom Premier Elite 24 with Smartcom module. I have a programmed a “Bedtime alarm” to arm all doors and downstairs PIR’s. I have fitted an external LED in my hallway which I hoped would illuminate when the alarm is part set to remind other family members, first thing in the...

Warning: this is a long post. Thank you in advance if you have the patience to read. Hi, I had an Texecom Premier Elite alarm system installed around 3 years ago. The alarm company that I used have been pretty bad on the customer service front (hence why I havnt just gone back to them with...