Help please for wiring a Hive receiver - thanks!

F

Fiona Walker

Joined
12 May 2021
Messages
13
Reaction score
3
Country
United Kingdom
Hi. I am fitting a new Hive and have what I hope will be a simple question :)

I need to replace the existing control unit (which is hard wired to my Alpha boiler) with the Hive controller

I can re-use the same wall plate which currently has blue going to the N terminal, brown going to the L terminal, no wires on terminal 1 or terminal 2 and then grey going to terminal 3 and black to terminal 4. Earth wire goes to earth.

When i take off the existing controller from the wall plate and replace it with the Hive controller, the Hive controller lights up at the appropriate time (so no issue with the Hive connecting to the thermostat) but the boiler doesn't fire up?

Can anyone tell me how I need to swap the wires around on the wall plate to make the Hive controller talk to the Alpha boiler please

Thank you very much indeed .................
 
What boiler, Is it a Combi boiler? Do you have a timer, if yes, This will need to be set to constantly on and Hive will override. Did you replace a thermostat or a programmer?
 
Hi Chris. It is a combi boiler. I have replaced the thermostat (with a Hive one) and the controller (with a Hive one). The issue is that when the Hive light goes green on the controller (wanting to start the boiler) is that the message isn't getting to the boiler, so it doesn't fire up. I just need to know which wires coming in to the wall plate need to go to which terminal. Thanks :). Fiona
 
The current controller (the one that I am replacing) is a Drayton Tempus 7 which currently has blue going to the N terminal, brown going to the L terminal, no wires on terminal 1 or terminal 2 and then grey going to terminal 3 and black to terminal 4. Earth wire goes to earth. I think I need to change the order of the wires around for the Hive controller to work??? Thanks
 
Drayton Tempus 7 appears to be a dual channel, eg heating and hot water? Do you have single or dual channel Hive?
 
Move the black wire that is currently in terminal 4 to terminal 1.
Done.
 
Hi Johnmdc. I had REALLY hoped that your suggestion would work but having moved the black wire from T4 to T1, boiler still doesn't fire up (the thermostat is on full and the green light is on on the hive controller) ??? Sorry. Any other suggestions please. Thank you so much
 
Fiona, can you post photo of wiring and Hive receiver? You said you replaced thermostat with a Hive and controller with a Hive, do you have 2 separate Hive’s or just the one? Also the existing thermostat, you need to either set to maximum or join live and switched together.
 
Last edited by a moderator:
I didn't get onto it that you had removed a thermostat.
As Chris pointed out you can't just remove it you need to join the live and switched wires together to complete the circuit.
Also as others have asked can you confirm that you have the single channel Hive receiver.
 
Hi Chris_W. Photos attached of existing Drayton (front and back)/ photos of Hive (front and back) and photo of the current Drayton in situ hard wired off to the Alpha boiler.
Dratyon in situ at the moment.jpg
. thanks everyone
Drayton wall plate with unit removed.jpg
Hive controller.jpg
Hive controller rear.jpg
Drayton rear.jpg
 
Okay your old clock was a 2 channel clock so it's a bit different to the Hive.
What you need to do is put the black wire in terminal 3, the grey wire (which won't be doing anything) in terminal 4.
Then you need to put a short piece of wire in to link L and terminal 1.
What have you done with the wire where the old room thermostat was? As I said before you can't just disconnect it.
It needs linking out.
 
As suspected and John says, you’re Drayton timeclock is a 2 channel (for heating and hot water control), which is why I asked if your Alpha is a combi boiler. John has provided with what you need to regards wiring, if you don’t have a combi boiler, you will lose any hot water timing periods, and consequently no hot water. If it’s a combi, you’ll be fine to follow John’s wiring and set existing thermostat to maximum or link out.
 
You must log in or register to reply here.
Back
Top