sent pm
Texecom Premier elite smartkey
- Thread starter Aaron Kent
- Start date
- Joined
- 30 Dec 2018
- Messages
- 33
- Reaction score
- 0
- Country
I understand your logic, I have used both Engineering and master codes but no luck.
Why should it not be used as an ent/exit it does the job ? I am using timed exit.
Why should it not be used as an ent/exit it does the job ? I am using timed exit.
should really start a new thread as User not been seen so nice 2019.PIRs should not be used as E/E zones unless in part set, in full set should be door contact on front door.
WRT going to the code page what steps do you go through and what happens.
i suspect you get o the user you want add smart key, then press yes rather than omit?
WRT going to the code page what steps do you go through and what happens.
i suspect you get o the user you want add smart key, then press yes rather than omit?
Thanks for the reply…this what I do
I enter the master passcode
I then press menu
“Do you want User Mneu” shows
I then press tick
“Do you want to View Event Log” shows
I then press the down button 10 times
“Do you want to Setup Users” shows
I then press tick
“Setup Users User002:” shows
I then press Omit
“Enter User Code> - - - - - -“ shows
Note if I go through all the same steps but don’t press Omit but instead press Area it does ask to register a tag…
I tried using the Engineer Code and pressing Omit at the first menu but all I get is “ All Devices Learnt”
The panel tells me it is
“Elite 24 Eng -> SW V2.11.09 LS1”
Which I understand is a Premier Elite 24.
It’s not a new system installed circa 2014
The user guide is INS555-2
I wonder if the panel doesn’t have the capability to register a Smart Tag?
The system has 3 door sensors and two smoke alarms … I think they are all wired (i can see the wire to two of the door sensors the third could be in the wall). All the room sensors are wired. I can’t tell the smoke alarms but they are in the ceiling so could be hard wired.
Any advice is much appreciated.
I enter the master passcode
I then press menu
“Do you want User Mneu” shows
I then press tick
“Do you want to View Event Log” shows
I then press the down button 10 times
“Do you want to Setup Users” shows
I then press tick
“Setup Users User002:” shows
I then press Omit
“Enter User Code> - - - - - -“ shows
Note if I go through all the same steps but don’t press Omit but instead press Area it does ask to register a tag…
I tried using the Engineer Code and pressing Omit at the first menu but all I get is “ All Devices Learnt”
The panel tells me it is
“Elite 24 Eng -> SW V2.11.09 LS1”
Which I understand is a Premier Elite 24.
It’s not a new system installed circa 2014
The user guide is INS555-2
I wonder if the panel doesn’t have the capability to register a Smart Tag?
The system has 3 door sensors and two smoke alarms … I think they are all wired (i can see the wire to two of the door sensors the third could be in the wall). All the room sensors are wired. I can’t tell the smoke alarms but they are in the ceiling so could be hard wired.
Any advice is much appreciated.
Can you confirm if a Ricochet wireless expander is fitted to your system?
Hi HandyMojo
I will go and look at the setup when I get home tonight but I am pretty sure there is not one installed.
I think that would be a separate box to the main panel ? I think there is only one box there.
Will confirm tonight.
I thought that might be the issue as everything is hard wired…but the user manual didn’t make it clear that a wireless expander is needed…. But maybe that is totally obvious.
Thanks for the reply. Will respond tonight with pictures…
I will go and look at the setup when I get home tonight but I am pretty sure there is not one installed.
I think that would be a separate box to the main panel ? I think there is only one box there.
Will confirm tonight.
I thought that might be the issue as everything is hard wired…but the user manual didn’t make it clear that a wireless expander is needed…. But maybe that is totally obvious.
Thanks for the reply. Will respond tonight with pictures…
Right I was wrong there are two boxes in the garage.
The large is the Premier Elite 24 panel
I’m not sure what it does but it seems to have play and stop and record buttons so it might be connected to the security camera system…. It doesn’t look like a wireless expander that I have seen on the internet….
So do I need to get a wireless expander installed to use a SmartKey?
The large is the Premier Elite 24 panel
I’m not sure what it does but it seems to have play and stop and record buttons so it might be connected to the security camera system…. It doesn’t look like a wireless expander that I have seen on the internet….
So do I need to get a wireless expander installed to use a SmartKey?
Attachments
Yeup don’t see a wireless expander there.
how many hard wired zones do you have?
how many hard wired zones do you have?
So if I enter the master code
Press the up arrow 7 times til I get to “do you want to view zone status”
Press tick
Then I can scroll through the zones and there are 16 in total….. seems each room/sensor is a different zone…
Is that the limit of the Elite Premier 24 box?
Press the up arrow 7 times til I get to “do you want to view zone status”
Press tick
Then I can scroll through the zones and there are 16 in total….. seems each room/sensor is a different zone…
Is that the limit of the Elite Premier 24 box?
I wonder if there were 8 zones in the panel, the
Am guessing here …..(obviously)….
Thanks for help…
Texecom CCD-0001 Premier 8XE Local Zone Expander for Premier Elite 24
Was added and so there are 16 zones now and all 16 zones are used up so the only way forward is to add aTexecom Ricochet 8XP-W Ricochet Wireless Expander GCD-0001
Am guessing here …..(obviously)….
Thanks for help…