alarm

Hi I recently resurrected a thread https://www.diynot.com/diy/threads/texecom-premier-elite-dreaded-no-ats-available.552302/page-3#post-4885561 as I had a similar problem. Per that thread I had no success in fixing the problem and asked a professional to come and re-programme. They visited last...

I have a TS690R wireless alarm system that occasionally, 3-4 times in 10years, gives a jammed indication. I can normally enter our the code to reset the system and it clears. But today it has been in this state, with accompanying beep every 60 seconds, for 9 hours! I have tried isolating at...

Hi all, I hope and trust you’re well during these difficult times. An elderly neighbour has an old Scantronic 9800 alarm which, due to worn digits on the keypad, has probably had its day. Her son has done a bit of research and ordered a Cooper/Scantronic 9651 system as a replacement – he...

Have an ancient C&K Securitech ST802 system, haven't had any issues with it over the years until recently, when we're all working from home and not leaving the house as much. Some setting has caused our alarm to go off every morning this week around 5:30 in the morning, to the consternation of...

I hooked up GX remote and I can set unset the alarm, view logs etc from my phone. I am trying to set up push notifications but fail at the registration part on my phone. I can register without a panel account and everything seems fine but I never get any confirmation email.I can get the account...

Hello looking for some advice I am trying to get a TCPA2B PA fob to work with me honeywell flex 50 alarm I have successfully added the fob to a user and also enabled the remote PA fob setting however when I activate the PA fob the lights flash on the fob but nothing on the alarm anything...

Hello, Are there any known ways of monitoring a Texecom Premier Elite system. We have existing monitoring systems that we would like to integrate our alarm system into. I know we can do basic monitoring with some aux outputs based on events but we would like to be a little more granular so we...

Hi everyone, I am currently getting some renovations done to my house so the builders took down the PIR sensors. Since then I get constant errors on tampers etc so I haven't been able to use it. They are now ready to put it all back again but have managed to lose the back plate on one of the...

Please help. I don't know anything about alarms. I accidentally shut off the electrical power at home for a few minutes. When I turned it back on, the alarm went off. I put the code in and pressed RESET, but it didn't work. After many minutes, it finally shut up by itself. But now the alarm...

Looking for some guidance on adding a pa to my flex system I have a pa alarm with build it resistors however no matter how I wire it it won’t work it I mainly get +mask error Any help would be amazing Am using the built in 1k/1k One wire to a/2t back to zone One wire to nc1 back to ov...

Hello - appreciate anyone spending a minute to read this and offer some advice. I've moved into a house with an ADT Galaxy 2-20 system (v1.10). The system seems to have developed a fault with the Viper shock sensors which won't allow me to set the alarm. When I view the status in the menu...

Hello looking for some guidance and help if I may I have just started a project to try install a Honeywell galaxy flex I completely understand it’s probably over kill for a house and someone will tell me it’s not for a DIYer but am having a go never the less I have it all set up and working...

Hi All, I have a Premier Elite Series INS555-3 keypad and would like to re-locate this. Mine is wireless, I assume as I cannot see any wires from the back. I have the engineer code too. Please help. Avy

Hi, I have a flex alarm panel. I would like to wire this sensor up to a zone but i am not sure what terminals on the panel to use. Any guidance would be appreciated. Thanks Jeramy,

Hi, I have a flex system and am looking to install a wireless shock sensor. Before I buy one Does anybody know how these are fitted to the window frame as i dont want to drill holes in my aluminium frames. Will double sided tape be ok? Many thanks for responding. Jeramy

Hi Last night my keypad sounded (alarm off at the time) and it showed a fault of +RF Entrance Hall It emitted a tone a few times before I entered my code to see the fault. It did it again this morning. Cant find this fault code in the manual. I think it relates to the wireless door sensor I...

Hi, I have a problem with my alarm system. Im not sure why the unit is beeping or how to stop it. I have replaced the battery but that hasn't worked. Any help on this would be greatly appreciated. Hopefully the video link below has worked. Thanks, Ashley

Customer had alarm installed a few years ago. Never any problems with the keyfobs or alarm. Last service was about 6 months ago. Customer calls today to say that all his keyfobs (i think he has 3) now wont set the alarm but they can unset the alarm... Any ideas?

hi everyone i have a scantronic i-on40 in part set mode with the following zones configured: zone 17 - hall PIR (final exit) zone 18 - lounge PIR (normal alarm) zone 19 - garage PIR (normal alarm) zone 20 - front door contact (final exit) zone 21 - back door contact (normal alarm) i only use...

Our Premia 9 burglar alarm is around 20 years old. We’ve just been woken up by the control panel beeping loudly and displaying battery fault error code- BF. Managed to silence it by pressing reset repeatedly but worried this will happen again overnight. Does anyone have the alarm user manual? Or...