hive 2 wiring advice reciever installation

Hey all, I've read many threads with others having issues with installing HIVE in place of Honeywell programmers. So following questions asked by others and investigating the behind of my programmer and the switch by the boiler i would just like to clarify I'm on the right path before ordering...

Hi all, I know this sort of question is posted a lot but I can’t find what I need specifically. My conventional boiler was replaced with an Ideal Logic Combi C30 yesterday. I asked the plumber to switch my Hive dual channel receiver to a single channel, which he kindly did for me, however...

Hi everyone I recently had a new boiler installed (Keston C30 Combi) with the Hive Active Heating Thermostat. I haven't used the heating till today as it was summer so I switched my boiler from summer mode to winter mode. When I turn my heating up on my thermostat it says its turn on and...

Hi all I am new to this but am very appreciative of all the technical advice that is been given. I am looking to install a new hive system and replace the ep2001 controller. I have read a lot of threads and that are all different to each other due to the spring configuration. From what I can...

Hi - I'm in the process of replacing my Danfoss RX1 receiver with my Hive receiver (connections shown below): The original Danfoss back plate is shown below: My questions are: Can I just move the wire from contact "2" to contact "1"? Do I need to worry about "Off" on a single channel...

Hi New to this so please bare with me. Please can anyone verify the wiring of a Hive single channel reciever into a Worcester 28cdi combo boiler. I have attached a diagram of the hive connections and also the wiring for the boiler connections. Some say leave terminal 4 on the hive empty others...

Hi everyone, new guy over here. I'm ok with electrical DIY, but plumbing (and central heating system) is not my strong side, so sorry in advance if I write something stupid. Now to the issue. I wanted to make my home a bit smarter, so I bought Hive Active Heating - Smart Hive Thermostat &...

Hi, Just moved into a new home and planning to replace the existing timer, for heating and hot water, with the Hive dual channel receiver, thermostat and hub. There doesn't seem to an existing thermostat in the house, only the timer. The attached images are of the existing wiring and the...

Hi, just moved into new property. As CH/HW programmer appears to have a standard back plate I have decided to install a Hive system. However, I'm stuck on whether to set it up for a pumped system or gravity fed as I'm not sure what I have. How can I tell? I have a hot water cylinder in the...

Hi Guys, been given a hive heating dual channel system, which seems to be correct for the system i have. i have a conventional boiler and a large hot water tank. on removing the original controller what i see is not what the manuals seem to suggest it should be wired. any chance anyone else...

Trying to replace Horstman 425 Diaem with a Hive. Problem with the old controller both HW and CH had to be in the on position for CH to work. There were 2 wires in the first on position and 1 wire in the second on position on the backplate. Rest were common positions and jumped across. Back of...

I am currently looking at installing a HIVE Active heating control unit to replace a Danfoss TP5. I currently have a 3 core and earth cable running to the existing heating controls (battery powered unit) I have attached my existing wiring diagram and the HIVE wiring diagram. Please also see...

I’ve just purchased Hive and after reading instructions am a bit dazzled as to the wiring for an old WR1 receiver and UP2 programmer. Can anyone explain how I link out either the timer/receiver? There is also a wireless room stat but I’m guessing just decommission by removing the batteries. Any...

Afternoon all After some advice and guidance. I am looking at installing a Hive Active System (was bought a hot water and central heating kit for xmas, consisting of 1 thermostat, 1 receiver and 1 hub). We live in a new build house that has two heating zones with 2 x Danfoss TP5000...

Hi Guys, New to this, so please be gentle :) I have just been given a Hive Active Heating system, single channel for a Combi Boiler and need some help with the installation. My current setup is a Potterton Promax Combi Boiler, which is connected to the mains via a fused spare. Installed in...

Hello, We just moved into a new house that has a Siemens therm installed on a Glow worm combi boiler. It works fine but I find it really complicated to programme so want to switch to a Hive as the prices are down for 'black Friday' sales. Before I install I just want to doublecheck the wiring...

Hi I would like to change my programmer (Danfoss TP5000si-RF / RX1) controlling my Feroli Modena 102 combi boiler to Hive 2. It seemed pretty straightforward to begin with but although the Hive receiver is working fine sending the on/off signal etc the boiler isn't firing up. I have checked...

Hi all, I have just bought a Hive 2 system to go with my Microgenus HE system. There is no existing external control system/thermostat and was all controlled by the internal timer, which can’t keep time. I think I’ve worked out the wiring but just want to check with you guys first as there are...

Hi All, We're in an absolute mess. Recently we've had a plumber come out to fix our heating and hot water. Both had stopped working. The first time he came, he changed a pump. This fixed the hot water - but the heating wasn't working. About a month later, he installed two new valves (Drayton &...

Hi all, I am trying to install a Hive receiver to my boiler after a colleague at ensured me that it was a doddle. I'm handy enough to get most things done around the house, but typically when I find myself unsure of how to complete something correctly, I aways end up making a totally wrong...