hive 2 wiring advice

Right. So. Managed to get a Hive thermostat dirty cheap on carboot sale. Looks new. Did all internet bits. Boiler is Independent 30. So u can hear clics whenever u turn it on/off. Had a simple 2 wires termostat before. Did loads of tries. Blue goes to number 1 brown to 3 etc. Linked tried a lot...

I’ve just purchased Hive and after reading instructions am a bit dazzled as to the wiring for an old WR1 receiver and UP2 programmer. Can anyone explain how I link out either the timer/receiver? There is also a wireless room stat but I’m guessing just decommission by removing the batteries. Any...

Hiya. New to the forum and I need I bit of help. I’ve bought a hive heating kit to install on an ideal logic combi boiler. There is a Honeywell wireless receiver next to the boiler that will be replaced by the hive. When I looked at the wiring the boiler is supplied from a wall socket via the...

Hi Guys, I have a Hive Active Heating and a separate Multizone ready to install. I am fairly confident in the way it works just unsure which wires to put where as I appear to have numbers 1-12 on my back plate currently! Any help would be much appreciated :) Danfoss Backplate by mrsarcysean...

Hi all, New on here. I’ve just bought a hive 2 thinking I could install it myself. My current Danfoss rx1 wires look like the image above. I now have rx1 terminal 2 in hive terminal 1. The rest is the same. I followed the advice of another conversation on here. The hive all seems to be...

Hi, Can anyone help with the wiring of my EP6002 programmer to Hive? I also want to remove the old thermostat and wires Thank you Vin

Hey, I have a new Hive thermostat. Looking to fit to a InTec² 28XE boiler. The boiler wiring is shown here: Boiler by DrRadar posted 6 Jan 2018 at 12:44 PM The Hive wiring diagram is shown here: Hive by DrRadar posted 6 Jan 2018 at 12:43 PM So far I have: Boiler Mains cable...

Hi, I am currently trying to install a single channel Hive to a Potterton Titanium boiler. I have ran a 4 core cable from the wiring on the boiler to the Hive. I’ve wired as follows; Live - Live Neutral - Neutral 230v Live Out - Common Switched Live In - Heating On (NC) I have switched...

Hi guys, I have just purchased a Hive 2 on offer at screwfix with a couple of bulbs, seemed like a great offer to take the plunge... I’m not going to attempt a self install unless I feel completely confident, I have both a plumber and electrician friend, either of who I will get in if I’m not...

Hi guys. I’m currently trying to install a Hive 2 in our granny annex. We have one main combi boiler and the heating is set up in 2 zones. One for the main house and the other for the annex. The annex has it’s own 3 wire (Sunvic tlx 200) thermostat and near the boiler there is a 4 pole main...

Hi all, I'm new to this, but I'm learning fast... I would like to upgrade my current 2 zone heating system to Hive. The current system runs off a district heat network to the flats with a heating interface unit in the flat. I have two HPA2 zone valves, two RET230P room stats and a TS715...

Hello, We just moved into a new house that has a Siemens therm installed on a Glow worm combi boiler. It works fine but I find it really complicated to programme so want to switch to a Hive as the prices are down for 'black Friday' sales. Before I install I just want to doublecheck the wiring...

Hi, I’ve got a baxi 28he platinum in a rental property. Its got an old back rf timer/thermostat that not longer works correctly so the heating has a mind of its own. I’m looking to replace it with a hive (or similar) but I’m unsure if it’ll be compatible. Any suggestions or help would be good...

Hi all, I have just bought a Hive 2 system to go with my Microgenus HE system. There is no existing external control system/thermostat and was all controlled by the internal timer, which can’t keep time. I think I’ve worked out the wiring but just want to check with you guys first as there are...

Hi All, We're in an absolute mess. Recently we've had a plumber come out to fix our heating and hot water. Both had stopped working. The first time he came, he changed a pump. This fixed the hot water - but the heating wasn't working. About a month later, he installed two new valves (Drayton &...

Hello The new owners of our house don’t want Hive installed, I’ve managed to acquire a Danfoss FP715SI along with a Danfoss RMT230. Can anyone give me a quick run through of wiring up the Danfoss from Hive wiring? Thanks for any help!

Need a bit of guidance here, ex sparkie so not a numpty, well not always :) Bought a Hive Active Heating 2 CH Only setup. So I have a dreaded ferolli boiler with universal clock as shown in Image1 Powered by a Switched Spur as shown in Image2. The Grey Cable is the 24v out from the boiler to...

Hi All, I am thinking of replacing my wired Honeywell programmer and dial thermostat to a Hive V2 and would be grateful if anyone can confirm a few things! I have a separate hot water tank. I have attached a few pictures of the wiring of the programmer and dial timer and labelled the photo...

Just thought I would share the wiring I used when I installed the single channel Hive receiver on a Greenstar 30Si boiler Addtional Information Hive Install Guide https://www.hivehome.com/attachment/37/download/Thermostat_Install_Guide.pdf

This is my current stat I'm looking to upgrade to hive, can anyone guide me to what wires go where on the hive stat. Atm I have 1, 3 core and earth going from the mains split across L N and heating on, there's another wire that goes off from the stat that is jut L and N this appears to go via...