hive

I've searched a lot for the answer to this question, so I thought I'd open it up here to see if anyone know how Hive actually works. I already have a Hive hub, and I'm now planning on using hive to control my heating. I only need to control heating as hot water is on demand (i.e there's no hot...

Hello all, I'm thinking of buying either Tado, Hive or Nest for my house. I live in a relatively new build 3 story townhouse in the UK with the Danfoss TP9000 thermostat / hot water programmer on the ground floor next to my Ideal Logic 15 boiler, a Danfoss TS2 sensor in the living room. Then...

i have Valiant Ecotech pro 24 ( 2011 ) model boiler and Hive dual receiver i wired up however heating wont switch off i assume its because of wiring and its not controlling boiler. my old relay box to wireless thermostat was wired up like picture attached. the Hive Reciever is wired up with...

Hi, I have purchased and attempted to install a Hive Gen 3. The existing set up was a thermostat (Drayton Tempus 7) and a WR 1 thermometer. Looking at the existing install and the wiring diagrams with the hive booklet I have assessed that I have an S-Plan configuration. So I have powered...

Hi all, I'm after a bit of advice and/or reassurance. I've recently had Hive installed (single channel receiver) via BG (British Gas) and it works very well, however, the concern I have is that the hot water has to be set to 'Continuous' via the switch on the left hand side of the boiler and...

Hello all, Probably my questions is weirdest you have seen. I have purchased a house last month and moved in. In this house we have a Baxi combi central heating. And I was given a Salus RT500RF Thermostat to control the heating. Now I want to replace this setup with Nest or hive and all my...

The above is a photo of my current Potterton wiring diagram. I’m trying to install a two channel Hive system. The issue i’m Having is with the live wire that runs into 5, can someone tell me what I should do with this? I’m sure I know what to do with the other wires but this is giving me a real...

Hi, I have an oil fed Geminox FCX 30c boiler (https://www.manualslib.com/products/Geminox-Fcx-30-C-4112227.html) which has REG 103 (FBR1) ambient thermostat connected to it (as well as an external probe thermometer) The boiler has a mains power cable that plugs into socket in boiler room and...

Hello, I had the bright idea to install a Hive system for my aging mother whilst cooking the turkey. Turkey is done, but not Hive. I have installed the hub and receiver. I haven't yet installed the thermostat. It is a gravity fed system. The problem is, I can't switch the receiver/controller to...

Hi All I've trawled through here and not found a thread that precisley matches my setup so rather than break rules and tag onto other posts have started this one! Has anyone got any experience wiring the hive single channel heating system to a glowworm 38cxi combi? I currenlty just have a...

Hi all, I have Vitodens 100-w and its combi boiler. But, I have got hot water and heating version of hive. Main supply lines were coming directly to old thermostat and then were going to boiler main supply, I have kept it same in the diagram below. Please guide: Where to connect 1 and L from...

Good evening, I am in the process of installing the Hive Receiver and just need to replace the Drayton Digistat 2. Can anyone advise, having looked at the pictures attached, what wires should go where? I have a Baxi combi boiler. The wires going into Digistat, are only common and on. The hive...

Hi, I'm replacing a Drayton LP722 and Digistat SCR with a Hive. Please can anyone offer advice on wiring. The Drayton Digisat+1 RF thermostat was located downstairs and the central heating would only turn on when the on button was pressed, and turned off by pressing the off button. Any advice...

Hi all, I am in need of a little help... Boiler: Worcester Bosch RD532i Current Thermostat: TR2 Room Thermostat New Thermostat: BHT-6000 I want to fit the new thermostat to the boiler, but the wiring is very confusing and even though I have extensive knowledge of renovation, some wiring and...

Another hive thread! Hi all wanting to replace my current digital timer/thermostat with a hive V2. I have a Worcester Bosch Green Star 30si Combi boiler. My current setup is as shown in the attached image. The thermostat is in my landing and boiler is in the garage. The boiler connects to a...

Trying to replace Horstman 425 Diaem with a Hive. Problem with the old controller both HW and CH had to be in the on position for CH to work. There were 2 wires in the first on position and 1 wire in the second on position on the backplate. Rest were common positions and jumped across. Back of...

Hello Guys I have been trawling the internet trying to get an answer after using the online "chat" for help with Hive. I don't know if anyone here is a wiz with these things? I have moved to a new home and after working out I needed a new "hive hub" I have the device, made and account and got...

Hi there, Another Hive post, I know, I'm sorry. We've recently had a Ideal Logic + 35 Combi boiler installed. The plumber knew we were going to install Hive so didn't install a thermostat or any kind of timer, just a spur socket. I'm trying to determine which wires go where... Can anyone help...

Hi All, I setup Hive 2 a while back for downstairs heating and hot water and it works perfectly. This meant that my upstairs rads were still controlled by a danfoss tp5000 programmable room thermostat in the bedroom. Ive been out and bought the multizone kit for hive with the plan to replace...

Hi I'd be grateful for some help on rewiring my heating/hot water system to accommodate Hive please. It's not a straightforward install as the hot water and central heating controls aren't on the same backplate at the moment. This is the present setup: Boiler is a Worcester Bosch 40cdi with...