nest

Hiya, I'm just getting ready for a bit of Sunday DIY but thought I would quickly check the wiring. This forum has been brilliant in getting me up to speed, but nothing wrong with a little confirmation from my peers! So... I think I've established that I can replace the Integral Timer in my...

Hello everyone. I've just bought a 3rd Gen Nest and am going to attempt to install it myself. I've currently got a Danfoss TP9000, controlling my Logic 15 regular boiler: Only trouble is, when I take the face off I'm greeted by this: I really wasn't expecting to see three Neutral...

Hi All, I'm wiring my Nest 3rd Gen Heat Link up to my existing central heating and water boiler (Baxi Megaflo 2 system boiler) replacing a Honeywell programmer. The wiring that is in at the moment has E, L, N, and two wires, one (black) for central heating and one (grey) for hot water...

bought a hive today and installed it seemed to work but receiver keeps going red after a while . Think I'd have preferred a nest so am going to return and get a nest which I'll place where the old thermostat is Here is a pic of my Honeywell 6400c backplate Left to right they are labelled N L 1...

Hi all, Apologies, another Nest example but I've not seen one for this boiler. We have a 13 year old powermax 185 (Yes, I know) that I'd like to control using Nest and Amazon Echo. I'm yet to purchase the Nest system but wanted to check my thoughts on the wiring before I go ahead. I've...

Morning We've finally plumped for a nest persuaded by the slight Black Friday reduction. I'd read a few reviews beforehand and most advised they were easy enough to install (I suppose that is dependant on the installer!), I've had a quick look at the current set up, which has the mains switch...

Hello guys new here, i just got a nest recently and I have a Boliermate II with a GlowWorm Boiler. Just wanted to confirm if anyone has ever installed a Nest with this setup and just to confirm if my plan is correct. BoilerMate2 by Gualter Guizado posted 20 Nov 2016 at 6:10 AM So my plan is...

Hello all Hoping to get some help here. I just got a nest 3 to replace my existing system. My boiler is Ferroli DOMIcompact F30B and a Danfoss thermonstat. I also have underfloor heating vents and fans controlled by a set of separate thermostat and control. Its a Danfoss clock thermostat...

Hi there specialists, I am hoping to replace an existing wired Honeywell T40 thermostat on my Ariston Microgenus 27 MFFi combi boiler with a nest learning thermostat. I have taken off the T40's cover and checked its wiring and it seems to have two wires into 1 & 3 but these bear no relation to...

Hi folks, Long time lurker here, registering to see if anyone can assist with this. I know there's a lot of flame for Nest-related questions but this is more of a side query. Ive got my current wiring documented & mapped out. All thats fine. I just want some assistance with the new hot water...

Hi all, I'm planning to buy a nest v3 and self install if I can. V new existing system was installed in my house about 12 months ago. If it's possible I would wire the heatlink in the utility room where the programmable timer is currently. I am hoping this has the connections I need to do that...

Hi, 1st post and I'm a bit of an amatuer (can do basic wiring) so be gentle... Basically I need to wire a 3rd generation Nest Heatlink to a Vaillant EcoTEC 937. Could someone please relate the Nest instructions to the boiler wiring diagram for me? I'm not sure which Nest instructions I should...

Hello all, I would a very quick bit of advice. I am planning to purchase A Nest thermostat this weekend but I want to understand how I can wire it first with my setup. Please in advance forgive me if I say anything slightly stupid but I have a good understanding of electric circuits so I should...

Hi I'm a newbee, looking to install a Nest thermostat in place of the current manual room thermostat and was after a little information and clarification before I start. I currently have a wall mounted mechanical Horstmann HRT3 thermostat which has x2 wires (which measure 12V on a meter) 1x Red...

Hi Guys, I am a little cheesed off as I have already done in 1 boiler PCB board which I will have to order in. My Set up for the ground floor is: 1x Vailant 637 boiler which does my ground floor heating and hot water 1x Honey well programmer 1x Honey well Room stat. and my system is Zoned...

Hi all :) I've just bought a NEST 3rd gen, and would like to use OpenTherm. The Nest 'doc' has me just using the OT terminals to control the boiler, but i've also read that it's a standard wiring (i'll replace the programmer) PLUS the OT. Does anyone have any experience with this? I've...

Hi, I wondering if somebody can point me in the right direction with the installation of a nest thermostat. So i have the nest 3rd gen and need to connect this to the boiler. Can anybody help point me in the right direction to which connections on the boiler side i require to use. The...

Hi, I'm hoping some body could help me i have a Halstead Best 50 Boiler (Ironic Name) pumped system with hot water tank The boiler is controlled by a Potterton EP2000 programmer. I can either have the boiler on or off at various times of the day what i am struggling to find out is can i...

First of all, sorry for a new post on this topic but on trying to join an existing thread I was advised from existing members I should start a new post myself so here goes. I currently have an Ideal Logic Heat 15 boiler installed on what I believe to be an S-Plan system. The boiler is located...

Hi, I've ordered a Nest Thermostat and I'm planning on installing it myself. I'm pretty comfortable getting stuck in with these things, and have replaced various components on the boiler (electric side only, I'm not crazy!), washing machine and dishwasher before. I've got the service manual...