oven

hi I currently have a hardwired oven but the new oven has come with a plug. The oven is run off it own 30amp mcb from fuse box. My plan is to run a spar from the hardwire to a new socket a little further away (think I saw in has to be 30cm from oven in regs?). As the current hardwired outlet is...

Hello, I am looking to purchase a new oven. My current oven is a 13 amp one connected to a socket which is part of the other kitchen sockets circuit. The oven I would like to buy is a 16 amp oven and I am aware I would not be able to connect it with the existing setup. However, I have noticed...

Hi all, I have just bought a house and currently removing the kitchen to replace and fit oven/hob. We would like to install a gas hob and electric oven (integrated) The kitchen does not have a dedicated cooker circuit. Below is a picture of what we have. My question is.... if I got an...

I'm just installing my IKEA kitchen cabinets, I'm using my Neff oven, not an IKEA oven. The Metod cabinet for my oven has the little chipboard backing. It says nothing about removing this for the oven. Would you just not use this piece? It seems like it would only diminish ventilation...

Hi, i am hoping someone can help. I tried taking a look at my Neff Oven Fan element ( Neff B1432N2GB/01) since the RCD kept tripping everytime it was switched on after about 30 seconds so I brought a new element. Now when taking the old one off I pulled too hard stupidly and now I’m not sure...

I took delivery of a new dual fuel range cooker today to replace my old built-in single oven. However, I want to see if I can hook it up to the existing circuit, as given everything at the minute, I can't get (or rather don't want to get) an electrician out. Here's what I currently have...

I have a tenant complaining the oven does not cook correctly, taking a lot longer than the food packages say. With the oven set 200c after the heating light has cycled a few times I measured the temperature, the top shelf gives 180 and the middle shelf 160, with the bottom shelf at 150. I have...

U shaped stainless brackets slot over the hinge pin and are bonded to the outer front glass door - red. "Red" patch is about 3cm x 1cm. Original goo was some sort of silicone I think. Back of glass is a white enamel type paint I think, or maybe it's white-surfaced glass. I tried sanitary...

Hi. Wonder if anybody can help with this please? We have a baumatic p632ss single oven. It seems that when it hits the temperature set on the dial, it trips the RCD. If I switch off at the wall, I can then reset the breaker. Otherwise i have to wait a minute or so. Setting the temperature...

Hi, I have a Neff Electric Oven (B14M62N0GB) (https://www.neff-home.com/uk/supportdetail/product/B14M62N0GB/01#/Tabs=section-spareparts/) There is a catalytic liner which sits above the top heater element in the oven which I've just noticed is hanging down. It has a single screw which is...

Hi All Looking for some advice on first fix wiring for our extension, before connecting ang getting certification on completion. Our new kitchen will have a bank of appliance... 2x single oven, 3.2kw/230-240v/manufacture required fuse 16 1x Combi microwave, 3.0kw/220-240v/manufacture required...

Hello guys. To accomodate a new 16amp / 3.5Kw oven, I have laid a 6mm T/E from my consumer unit to a new 45amp cooker switch, going onto a CCU. There is a spare 16A MCB in the consumer unit but my calculations tell me I need a higher rated (19) MCB. I = 3500 / (230*0.8) = 19.02 Can some...

Hi - I currently have a 6mm radial (32MCB) to a 45amp cooker isolation switch (above worktop level) with a 6mm connection into a CCU. The radial runs under a timber floor, into a skirting duct then is clipped to the wall behind the units - No RCD protection. I want to replace the CCU with a duel...

Hi, I am NOT an electrician; but I spotted something that I thought was weird or bad practice. A friend had her house mostly rewired by electricians a few months ago. She already had a separate 32A MCB and circuit for Oven/Hobs with a 6mm T/E cable. And the electricians decided to use that...

Hi, I have a Creda Contour Electric cooker. It's old, but it's been reliable up to now. Today, both ovens have stopped working. To be exact: Working: hob-all rings, grill Not Working: Top oven (same compartment as grill), bottom oven, fan, clock Anybody know where to look first? Thanks

Hi We have fitted applicances set into the floor standing units at waist high. An oven is beside a microwave + warming draw. This looks great as a matched set. I am now electrcial having problems and want to replace the matched set with another. (+££) I am unable to find anywhere that will...

Title says it all really. Bit nervous about messing with this as all the bayonet fittings I've seen don't look like this. Any advice would be appreciated!

I’m having a pair of new ovens installed during a kitchen refit and I’m a little confused about how my electrician has decided to connect them. The ovens are Neff B57CS24N0Bs and are rated at 3.45kW. They came with cables naked 16A/230V and the instruction require them to be hardwired to an...

Hi all, looking for electrical advice. Have a Bosch single built under oven (approx 6 yrs old) - has started to trip out the RCD on modern fuse board but can't find a pattern to it. Mainly happens when been on for a while with lots in (sunday roast etc.). Each time I have been present when...

Hi all. Amateur but competent DIYer here. Looking to replace our built in single oven but our current one must be older than it looks because I can't find anything online that'll tell me what amperage it is. It's a Rangemaster PRSOESS 6013 if that means anything to anyone. 2950 watt. Some of the...