pyronix

Hi all, since yesterday, my Pyronix Enforcer 32-WE alarm at home (which uses the Digi GPRS SIM module) has not been polling according to the Pyronix cloud, yet I can still send and receive SMS messages associated with the GiffGaff mobile number associated with the panel. Has anyone seen or...

Hi all, I need to replace an old (2012) Pyronix Enforcer panel as the display has faded to the point that it's almost unreadable. I have an installer lined up to supply and fit a new panel (hopefully a recent V11 version), but they don't seem to be familiar with the latest firmware. I'd like...

Hi, I am doing some renovation knocking a wall down and need to move a pyronix control panel. I need to disconnect it from the electric and it will be off for about a week. What is the best way to do this please. Do I have to disable all inputs first? Then add them again when I put the panel...

Hi everyone I am upgrading my Enforcer from V9.51 to V11 using the Pyronix Enforcer V11 upgrade kit, which comes with a new PCB and associated kit in the box. I notice that a new power cable that goes from the PSU to the front panel is included in the box, and this has an additional flylead on...

After some advice gents. My alarm panel keeps triggering for tamper on the sounder. It's been fine for years. I went up recently and replaced the battery (as this also recently began to warn). Battery warn for sounder is gone but tamper remains. I tried checking the pcb and housing was...

Hi All, Thank you for your time. We're moving into a new home in 2-3 months time and wondering the best way to secure it as we are strangers to the area. We had a burglary at our current house but at the time, we had no alarm system or insurance. Can I ask if it is possible to wire a texecom...

Hi all, Can someone help me. I have installed a new Pyronix enforcer 32 and a delta bell siren. The existing wiring was already in the walls. I’ve wired up as followed: Backlight Disable >>>> not used T >>>> Com on main panel T >>>> 0v on bell with 2k2 resistor Eng. Hold >>>> Not used Bell...

Hi, Sorry if this has been discussed already. I have a 2015 enforcer running I think V9 with a hardwired cable to my landline. When triggered the alarm would dial up 07758 49993 and I would receive a text. This now says ARC Call Fail and I believe the service was recently switched off...

Hello all, I am really hoping that you can help… I have recently bought a house that I am renovating to move into. There is a Pyronix Paragon Super alarm system installed. I do not have any codes, and cannot contact the seller for them. I have downloaded the annual and have tried using the...

Hi all I have a strange issue, I changed the battery's (BATT-ES1) in my siren a couple months ago and after about a week, the alarm started to show the warning, Siren Wireles Low Batt. I asked the supplier to send me some new batteries, which they kindly did and I installed them and again the...

Hi folks The siren battery in my Pyronix enforcer needed changing so i bought two ES1 types form amazon and put them in following a youtube video. The siren then randomly went off intermittenly for 15 mins but then reset. This was on Sunday. Now i get a Siren1 Wirls Suprvn Fl error which i...

I had an old internal speaker (16ohm 12v) from my previous wired alarm setup that I wanted to reuse / add in the porch so we can hear the confirmation beep when setting the alarm I wired the positive and negative terminals of the speaker to the EUR-064 keypad (+ and PGM1) terminals. Only...

My alarm was showing a Battery Fault 100 error, so I replaced the battery and all appeared to be well initially. However, after a few hours the Battery Fault returned, and shortly after that Low Volts. I'm wondering if there's a PCB fault that's discharging the battery? Any ideas please?

With the Pyronix Enforcer WE v10 panel, I know it comes with Wi-Fi built in as standard, but if you get the GPRS SIM module, does it replace the "built in" Wi-Fi module or is it in addition to it? I.e. can you install the GPRS module in addition to what it comes with OR would you need the v11...

I am in the process of replacing my old out of date wired alarm system with the Pyronix Hybrid Euro46 Small V10 (Grade2) Control Panel and Wired PIRs ( Pyronix KX10DP ) and Wired Pyronix DeltaBell X Module But on wiring up the PIRs I have come to a problem with the instructions that came in the...

I moved into a house with a Euro mini alarm plus a pyronix v2 tel unit. Never had a problem with it, but we don’t actually use the alarm often. We came home to the internal speaker making a constant alarm and the main alarm panel showing error code 485 loss of Comms please wait. No buttons...

Hi all, I recently moved into a new rented property that has had an Enforcer alarm fitted by a previous tenant. We have keyfobs that seem to work to set and disable the alarm so that's good, what we don't have (and neither it seems does the property management agency) is any sort of PIN code in...

The system is installed in a 2017 new-build and comprises a Pyronix Euro Mini Prox, with Euro Mini control panel and MEQ Blue PIRs. The PIR/Detectors are connected as per DEoL configuration, with the zone wiring entering via the N/C terminal, passing through two resistors in serial (4k7, 2k2)...

Hi, I keep buying batteries for me forb but none of them fit. I am starting to think there must be many different versions. However my forb doesn't have any distinguishing marks, even when I open the flap at the back to replace the battery. Are there different version? If so how do you...

Hi all, I had an alarm professionally installed. However the company has gone bust. Things have worked fine for 6 months however today, (you know how computers are, work fine, change nowt, then next day doest work :-/ ) I cannot log in through the app on my iphone. My usuaal way of...