pyronix

Hi I received an email stating I will need to upgrade to Home Control 2.0. After installing the new app on my phone, I entered my home alarm credentials but at the login screen it states... Access denied. Before you can access this app, it needs to be authorised on the pyronixcloud. Please...

Customer had alarm installed a few years ago. Never any problems with the keyfobs or alarm. Last service was about 6 months ago. Customer calls today to say that all his keyfobs (i think he has 3) now wont set the alarm but they can unset the alarm... Any ideas?

Hi all, Looking for some advice on location for a pyronix enforcer alarm panel. I want to be able to wire it to a deltabell lightbox. Is it simply have it installed in the attic as I can’t see me being able to wire it down to the hallway area? thank you in advance!

Hi could anyone help please. Am not able to set alarm after changing the sensor batteries. Active Faults 1. Kitchen Wirls Supervn F1: Full Set

I have completed a replacment of my old Pyronix alarm system to a new feature packed Pyronix Euro 64 v10 with th Keypad Eur-064. I have managed to configure all 8 onboard zones (imputs), the bell & the keypad. The only issue I am facing is that I now wish to add a PIR using one of the 2 Keypad...

Hi all, New member here and in dire need of help with my alarm. I have set it all up myself and has been working perfectly fine for years, however I now have the added complexity of having a dog in the house.... When we leave her alone in the house (downstairs kitchen and lounge have PIRS) she...

Hi, We've had a pyronix enforcer alarm for around 3 and a half years. Not sure on model. Last month it came up with wireless batt fault so i replaced them all with cr123a and the problem went away. This morning we were woken by the same fault. Other than the obvious - one of the new...

Hi all, New here and Looking for some help if possible. i have a current (but dated) working alarm with 4 wired pirs, wired bell and wired door contact but need 2 new pirs that can’t get wires to. All wiring working and in very good condition. Having a pyronix enforcer fitted (want an app based...

I am having a problem with my mother’s alarm system (Pyronix Enforcer). Before going any further I need to clarify that this is an exceptional situation due to the Coronavirus lockdown, that I would, under normal circumstances, get sorted out in a heart beat by simply calling an engineer in...

I have got an issue with the siren outside the house, which has started triggering a "tamper" alert which is quite deafening. Currently waiting for the electrician to look into that, but in the meantime trying to reduce or stop it altogether. Been into engineer mode, but am unable to find the...

Hi, We have a Pyronix wireless system installed just over 4 years ago and have had Wireless Low Battery Siren messages and alerts for a few days. We have dummy alarm boxes externally, but as far sias know only the internal panel siren. Once I opened the panel up I could check the internal...

Hi, Hoping someone can help.... I've fitted a lightbox module (FPDELTAX-Light) to the inside of the lid/cover (FPDELTA-CW) but can't seem to close the lid. The lightbox cable gets in between the lid and deltabell x module (FPDELTAX2MOD). The back plate is FPDELTA-BDB. What am i doing wrong...

The other day for the first time in 4 years, my Pyronix Enforcer Home Control+ panel started beeping and went into a fault condition for the first time under a normal idle state. The error what I believe caused the "fault condition" was a "SMS call Fail" event, although not sure why it...

I have a warning (amber yellow triangle) with the message “Active Faults Service Required”. This appeared at midnight exactly and the panel log has “00:00:00 Service Required” There have been a couple of log entries in the three days since the warning showed. They are both: “Wireless Ch To”...

I’m in the market for a monitored home alarm system, to be installed professionally. No DYI – so I hope this question is not off-topic, but I’m asking here in the hope people will be familiar with all aspects of how alarms work, not just DYI. Most installers in my area install either Texecom...

The battery on the Deltabell siren box outside my property has gone, and I need to replace it. The siren is intermittently sounding, I assume because the battery is low and causing fluctuations. I just wanted to ask someone whose replaced the battery how easy is it to do? I need to go up a...

Hi folks, I have a friend with an Pyronix Euro 46 panel connected to Pyronix cloud through a small alarm company. He wants to take control of the panel himself but the company refuse to release the system from their cloud account as he is under contract. I have a fair amount of experience...

Please help...we are trying to install and set up the enforcer v10. We have a bungalow with one entrance/exit door which we are trying to add the sensor to. We also have the external bell which needs to be connected/learned. Then we have 4 vibration window sensors. We have only attached the door...

Hi, I have a Pyronix Enforcer system installed in my flat. Recently I have had a few faults come up, mostly about low batteries, and that’s fine, I can set about getting the batteries changed. My problem is that when those alerts come up, it causes a repetitive double beep from my control...

Hi all I’m not new to alarms, having installed many texecom (hard wired) veritas products in the past, but the Pyronix enforcer V.10 (wireless) totally has me stumped. Really confused regarding levels, zones and areas. Everything is installed, as in devices learned, signal strength test ok...