upvc

Fitting a window in an hole that is 40mm out of true top to bottom & has an arch at the top. So, have frame extenders for sides and top- question, should I mitre them where they meet or just butt join? Q2- what's the best blade for cutting pvc in my mitre saw? TIA

I have a conservatory with French doors but the slave door cannot be opened because the Concealed Operating Lever to open the slave door is broken / missing. I have tried locksmiths and windows repairers but they do not know what the part is in order to replace it. The conservatory was...

Had these windows installed last year and I've always thought the fit looks wrong. I can't help but look at it everyday. The base of the window is thicker then I have ever seen in anyone's house and I always wondered if it was measured short. The previous windows were much less intrusive only...

hello im struggling to find an Ali reinforced corner post for upvc any help please?

Please see attached pictures. This window seems to have dropped a little and there is a gap at top which lets in a lot of road noise & draught. The window itself opens & closes perfectly. Windows are in place about 13 years. Any thoughts on what I need to adjust to seal it up. Many thanks.

I am trying to clean some uPVC window frames, but the internal corners have been finished with something that does not seem to be silicone. It is quite hard but comes away with scratching, which I don't really want to do. Whatever it is, it is thin with no significant depth. Any thoughts on...

I am looking for suggestions of techniques or tools for removing old and perished bubble/flipper gasket from the narrow slot. Where the old gasket material has gone very non-flexible (mostly along the bottom edge), I have found that the barbed section just tears or snaps where it joins the...

So it would appear that the manufacturing company have provided the French doors for the Juliet balcony with concealed/bottom drainage holes instead of face drainage holes despite the fact that they knew it was for a Juliet balcony with no seal. The water gets blocked inside The trim...

Not seen a previous post on this so thought I'd ask the question -- how can I both remove and seal up trickle vents? I know what they're for but they get clogged up in the summer, only allow a small amount of air flow and they allow more sound into the house the rest of the time. We ventilate...

Hi I'm in a spot of trouble, last night I opened my window to let some air in but as I've closed the window the hinges jammed and bent. After some research I realise that these hinges aren't expensive or difficult to replace but my questions are which hinges do I get and will the new hinges in...

Yet another post on uPVC doors I know... There are three roller cans on my back door — bottom, middle and top. The top and middle pull the door into the frame tightly and there is a good seal. Unfortunately there is a gap at the bottom and I can quite easily push or pull (from outside) the...

Hi Our kitchen window has leaked since we moved in, the previous owners tried to fix it by outing sillicone everywhere. Last year we got a window man out and he redid all the seals but said it might be an issue with the render. With the recent bad weather the leak is back, I woke up this...

Drilling into granite is, i've always found, a pain. Perhaps I'm using the wrong drill bit. What's the best drill bit/ fastest way & method to make a hole in granite for fixing the window?

Hi, For an outbuilding, we have 9inch (220mm) roof joists and 4in (100mm) insulation and 18mm OSB3 boards for a warm flat roof. Based on this I think I will need at least 340mm Fascia boards - but I can't seem to find any; most seem to go up to 225mm only.. I was planning on using 18m fascia...

I have been looking at replacing some perished uPVC door and window gaskets, and taken aback by the *huge* range of types available. Would I be horribly incorrect in assuming that if the barbed rubber 'arrow' section is the right size to fit in the slot, and the bubble or flipper sections are...

The outside of my unusual conservatory needs finishing. Above the doors is a 152 mm steel beam (approx. 4.3 m), which has the grey factory coating. On top of the steel are aluminium window frames - with no sill - in RAL 7016. They are only a few mm behind the front of the flange of the steel...

Hi all, just afer a quick bit of advice. Am looking to get some French doors installed in place of an existing window. Got someone in to measure up & quote for this. All ok so far, until the final measurements are taken Dude says we *must* have a fan light because the doors would be too...

Had a look on line today and got a number of prices for windows. Currently have wooden ones and want to stop having to paint every so often. So going to make the change. Anyone have a view as to whether there is one supplier out there that is significantly cheaper than the others, and still...

Garage doors are framed with timber. Base of timber has rotted. Wish to replace with white UPVC or other that requires no maintenaince, so never have to re-visit, or re-paint. Sizes needed are: 70mm x 70 mm x 2300mm (size is like a solid fence post except perhaps longer. Does not have to be...

I'm going to have our old Rehau upvc front door and sidelight replaced. Things seemed to have moved on a bit since it was fitted. Can someone explain the difference between composite and uPVC, and any pitfalls/brands that are good or should be avoided? There are tales on here of peeling...