wood

Hi All, I am looking to install stair panels (wainscoting) however I am struggling to find a trader online to carry out the work. What is the right trade for this type of work? also if anyone has any links or contact to someone in the London/Hertfordshire area then please do private message...

I have a dark solid wood floor in my hallway. Recently I've had to do a bit of filling and sanding of the walls and ceiling in the hallway, and unfortunately, despite my best efforts, some of the very fine plaster dust has got into the grain in the wood floor, leaving a white "bloom" in certain...

Hi all, Coated my wood floor with Osmo Wood Wax Extra Thin Hardwax Oil this morning. Waited an hour as it was dry and the wood had sucked up the oil and applied a second coat, as per instructions. Now however, it's an uneven finish which doesn't look great. When I do a 'scratch' test on the...

Hi All, I would like your opinions regarding a labour quote I have received for fitting door frames, architraves, hanging new doors, block door opening to make a wall, fitting 2 PVC front home doors and make new double door opening and fit frame and doors. These are the prices below per job...

Hello! We have uncovered the original Victorian floorboards in our house and we'd like to keep them exposed. What's the best stain/dye to use after sanding? We're looking for something which looks quite natural but is darker than the light colour of the wood as it is. Thank you

How do i seal in black mould on wooden door and skirting boards? The wood has a yellow gloss base-paint/undercoat, from i guessing twenty years ago looking at the paint tin[ i inherited the house]. on top of that is 3yo matt white paint. The black mould is under the white paintwork, but not...

Tried to bleach out some mouldy grout in the steam room where I have 2 wooden racks for sitting/toiletries, etc. New mould remover left some bleach marks on the wood (photos). I'm completely inexperienced in fixing this sort of thing (if it's even possible), so after some research it seems to me...

Hi all, I'm putting 10 x 2 joists in for a flat roof. The span is about 3m from wall plate into steel and then the same out of the other side of the steel to the fascia. The steel section is 254 tall so I've gone for 10x 2 to give a flat roof and a flush ceiling. Can anyone advise on the...

Hi, My partner and I are making a outdoor clay oven, based on an old terracotta chimney topper like this on, but the top of it is closed off. We were planning on turning it upside down and building a stand and "roof" for it. However we cant work out how the create a stable stand, as the bottom...

What glue should I use for joining Tongue & Groove Engineered Wood Flooring? EWF for approx. 15mm thick and will be installed as a floating floor (installed on typical water-resistant underlay). Sub-floor is concrete and relatively flat. Thank you

Hi all I'm tearing my hair out trying to find some glue to hold door knobs together. I have a metal bolt type element (a furniture joint connector type with a cap nut) and a wooden button which i'm trying to affix on the front. I started with epoxy, followed the instructions and they lasted a...

Hi, Due to flooding our engineered wood floor has become wet. Now that it's dried out again it's got some wider gaps in some places. At the largest spots up to about 5mm wide. What filler do I best fill this with? The flooring is varnished and surface looks good, so it should not be something...

Hi there, We have a 1900 Victorian terrace whereby the floorboards are not in good condition (we sanded them when we moved in and they are structurely sound) but a mixture of 1900/1950 and a few chop outs from previous owners etc. We like the exposed flooring and therefore would either like to...

Hi everyone, After recently purchasing our property, I've found some patches woodworm holes in the main roof joists. They are mainly at the upper half of two joists and from what I can tell they don't seem to be active. I've attached the photos below and would appreciate any advice given. Thanks

I've just taken the 1970's ceiling down in our 1780's cottage... it was quite shabby and the insulation above was old mattresses and sofa cushions! So we're now wondering how to reinstate the ceiling without disturbing the breathability of the room... if anyone has any thoughts I'm all ears...

Hi Can anyone give me any idea what would be best to change a door to a window. Its a old concrete house old pit house and the door is approx 3ft the old door was wood. Do I clover the gap with wood or brick with cavity?

Needed to drill some holes through joists for a lump of 6mm T & E for a new shower. My trusty flat bits struggle through the 200 year old Douglas fir so thought I'd treat myself to some shiny new bits- these puppies...

We have a 40mm solid wood beech worktop fitted in our U-shaped kitchen. Two lengths and a third breakfast bar. The kitchen and wooden worktops were bought and delivered a year ago. Due to various reasons (including my own slow DIY skills) we have only now got to the point of fitting the...

Hi diyers, Varnished a sleeper (untreated don't worry) coffee table last night that I have been building and am all of a sudden cautious about placing it in the living room. I don't want it to stain the carpet, no less so because it is a light carpet and only a rental!! Should it be alright...

Hi all I want to replace a load of panelling on my old shed. I've found some shiplap to match what's there but it's softwood and untreated. What's the best stuff to use to give it a good 10 years of life outside in the wet? Can I use creosote? Or is there something more suitable? Olly