hive

Hey Folks, I've inherited a ball of wires at the back of my EP2002, wondering if anyone can assist me with what goes where in the hive. There are similar posts here, but my ball of wires is quite different. The boiler is a Worcester Greenstar 40CDI Classic Regular. Heat only, so CH does the HW...

Hello everyone, I'd like to replace my DUAL channel Programmer made by Polypipe with HIVE mini receiver. I am not sure about the wiring. The old polypipe programmer use 2 AA batteries. HIVE use live wiring (N, L and Ground). Here everything is clear. Polypipe has dual pairing: C1 - Brown...

Hi I have just switched an old thermostat to hive. I am not sure the old thermostat ever worked. Essentially the boiler is not responding to hive and the heating is constantly on. I have used the same wiring configuration on the old thermostat and havent touched the wiring on the boiler. Do I...

Hey everyone, first time posting here but I am completely at a loss - looked through lots of the other posts and they all cover parts of my problem, but not the whole thing! I bought a Hive dual channel as I incorrectly thought that's what I needed - turns out I only needed a single channel...

Hi guys, new user but have relied on these forums a few times in the past so a general thanks to all who make this such a valuable resource. I am looking to install hive to my Baxi ecoblue advance Combi boiler and was happily following an older forum post about it but there is an ‘issue’ that I...

Hi, I’m new so apologies if this has been asked/resolved before. I had an engineer install my Hive Heating System yesterday, however, when I try to control the heating from the app or thermostat the receiver clicks on but it does not fire up the boiler. All the lights etc area solid green...

I’ve wired in a hive heating single channel receiver to replace a danfoss fp720 controlling a valliant ecotec exclusive 843. I’ve wired it up using the install guide from hive using earth, neutral, live, 1 & 3. I’ve wired HTG on from danfoss into HTG on in hive and what was DHW on into Common on...

Sorry as I’m sure you have seen 100 of these. But from looking at the past posts it’s wired up right so I’m at a loss here. It’s all running fine apart from the fact it won’t fire up. It’s also a single channel any help would be greatly appreciated

Hi there - looking for some help on hive wiring - I have an existing programmer that I can’t make any sense of the wiring on: The diagram on the existing timer doesn’t seem to match: I am trying to translate this to a single channel hive receiver. There is a wired thermostat in the hall that I...

Hi everyone - I’m hoping I can get some insight into why my central heating won’t turn off when told to by the Hive receiver. Boiler: Procombi Exclusive 24 Hive: Single channel receiver No previous thermostat had been installed I’ve got a cable going from the Hive receiver to the same fused...

Hi all. First post so bare with me! House setup - Ideal Logic H18 boiler and Kingspan Tribune XE, Hive active heating installed with multi zone (2 controls) Hive dual channel receiver wired to the boiler and a single channel receiver wired to the Tribune XE. We have been having issues with...

Hello, I’m hoping someone may be able to help me. I’ve moved to a house in a rural location where oil powers the heating and hot water. It’s a Grant boiler with Potterton control. I note that Hive suggests getting it installed by an oil boiler professional to check that it’s actually...

Hi, long story short my hive has been wired using a dual channel receiver on a viessmann combo boiler. Since removing the hub as I’m moving home, it only fires the boiler when I boost the hot water on the thermostat. Spoke to hive who said I should us the single channel receiver for the new...

Hi all, I am looking to get a Hive thermostat installed but wasn't sure if it was compatible with our oil boiler as I recently found out the Google nest wasn't. Any help and advice would be massively appreciated!

Hi everyone, I'm looking for some advice. I replaced the “invisible heat” thermostats and wiring centre for a wet underfloor heating with Hive. The underfloor heating has 4 zones with a thermostat on each zone. The engineer installed one hive receiver for each zone. Four in total. So...

I have pumped hot water and CH on a three port valve, a Y plan I believe The wiring seems standard to many Y plan diagrams, where there is no wire to terminal 2 (Heating off) on the controller My guess is I need this wired up for the hive to function fully, but where should it be wired to? The...

Hi there, First of all, thank you for your time. I'm looking at replacing my Honeywell T40 thermostat which serves pretty much as an on and off function on my home heating, I've a combi Vaillant boiler and the thermostat is wired to 1 (red cable) and 3 (orange cable) terminals, using the...

Hello, I'm using a Dual Hive for Combi (I'm using this and not single because it got it soooo cheap ). I have researched as much as i can, before asking. Have I set this up correctly ? Hive = Boiler Earth = Earth N =Blue L = 230v Live Out 4: Heating On (NO) = 1 References used ...

Hi all, Sorry to add another thread but I’m looking for some help. I have installed a hive v3 water and heating replacing my old st699. This was prompted by removing the old thermostat that I thought wasnt working and doing nothing to find it was infact setting the heat of the house and plunged...

Hi, I got a plumber round to change the pipes for 3 radiators to one. They aren't quite in the right place but luckily there is some give so at a stretch we can make it work when we install the radiator. He quoted to do this and install Hive for £160. Seemed like a nice guy until he broke the...