hive

Apologies if this has been asked a 1000 times!! BUT... Iv gone and brought the self install hive theromostat kit to place the honeywell heating system. Now going by the install videos on youtube i thourght it would be just a case of a straight swap another reson why i brought the dam...

Hi All, I just bought a Hive and want to double check the correct wiring. I have currently installed the Honeywell BDR91 (to Hive - Combi Boiler) like this: Would probably wire it as the following, but hopefully someone can confirm or correct the setup: Thank you!

I recently installed a hive dual thermostat to work alongside my Worcester Greenstar 34Cdi classic. The water side of things works perfectly. Boiler fires up, hey presto. The heating however does not fire the boiler. The heating only works if the water is on as well. Anyone got any ideas. Please...

Hi everyone I was hoping to have some help with wiring a HIVE 2 receiver to my combi Bosch Worcester Greenstar 8000 boiler (GR8300iw). I've had a look at several youtube videos and posts on this forum but can't find a specific guide for my bolier. (There are similar Bosch boilers but the...

Hi Have just purchased a Hive Active heating kit (heating and hot water). I've been browsing the forums and can't find anything relating to my current setup, so hence this new thread. My current system is a Worcester Bosch Greenstar Ri bolier (conventional not combi) so I have a hot water...

Hey there, Wondering if someone could give me a hand with wiring up a Hive to my combi boiler. The current wiring looks like this, boiler wires on the left and power and thermostat on the right. Its all just wired into a big connector. The boiler has 2 black wires rather than a black and grey so...

Hi my very first post so hoping that i can find some advice please. I have read a few older posts relating to this topic but have a pretty quick question i think. Where do i place my two hive receivers? From the research i have done for my boiler and system, which is two zone heating...

I have just moved into a new house which has a combi boiler (previously normal with HW cylinder) however the owner retained the Centaurplus C27 clock and just had hot water set to 24/7 to give a live to that circuit. Coming to replace with a hive single Chanel unit and looking for some help. At...

Old Siemens reciever https://i.imgur.com/5nzTFkW.jpg New Hive https://i.imgur.com/lqLys57.jpg I wired this up yesterday but no lights came on at all, checked the wiring and it all looks fine, figured it was a faulty receiver but not sure. One thing I'm thinking is that I know the siemens...

Good evening, I'm planning to replace my hortsmann centaurplus C11 with a hive thermostat. It seems like a simple swap, but I just wanted to check that I wasn't completely misunderstanding the wiring. Below is a picture of my current wiring and the wiring diagram for the programmer. It is...

Hi everyone, I have just tried to install Hive to my CH system and that didn't go well, I have got Ideal Logic Heat 12, Danfoss TP9000 Si, Danfoss TP5000 Si and small remote room temp sensor in the hall. The heating is twin zone heating + hot water cylinder. When I replaced Danfoss TP9000 Si...

Hi, I have today wired up the Hive thermostat, receiver and hub. Connected up the wires how they were on the old receiver and now the boiler is not working. Works from the main thermostat to receiver, but doesn’t action the boiler. Have now taken off the plate on the boiler and can see...

Hi all Puzzling one which my local heating engineer can't solve, who gave the boiler a clean bill of health but doesn't know much about Hive. I'm obviously not an engineer but I'm convinced the Hive wiring is at fault here somehow. The system was installed before we moved in. I found a similar...

I've read several threads on here about Hive installs, seems to be a fairly popular DIY job! I've also watched a few YouTube videos -and decided I would buy: https://www.screwfix.com/p/hive-active-heating-hot-water-thermostat/5215j?_requestid=284429 This may be a stupid question but want to...

Hi, I’m looking for some advice if anyone can help. I have an ideal logic 30 combi boiler and have fitting hive smart thermostat. I wired up the receiver correctly (I think) but the receiver doesn’t fire the boiler up when requested. The boiler currently only has a dial type timer fitting in the...

I see this has been asked may times and already some suggestions, just wanted to check my particular set up before wasting my 2 days off work! 1)Currently have BG UP1L(RWB9) Programmer. Can this be straight swapped with Hive 3, ie click on without rewiring? 2)If it does, next up is Thermostat...

Hi all, I am in the process of updating our heating controls. Looking to install Hive as we had it at a previous house and simply want to utilise the app as we work shift work so do not have set schedules. I am looking to install this myself as I always like to attempt in the first instance...

Have searched the site for solution and couldn't find one for my problem, hopefully someone is able to advise on where I have went wrong. Formerly had potterton EP2002 controller connected to my BAXI system boiler 60/100. (See photo) This also had a thermostat wired in and has a hot water...

I hope someone can help, We have a Mitsubishi ground source heat pump system with a water cylinder with a Mitsubishi PAC-IF013B-E Unit on the front. Downstairs we have a wireless Danfoss TP500Si thermostat which talks to the Danfoss RX1 single channel receiver also attached to the unit. There is...

Hi all, I hope someone can help. I recently purchased a hive dual channel receiver for my Worcester boiler which works alongside an immersion tank. The existing system was a Honeywell setup consisting of: - Wireless thermostat (battery powered in hallway) - BDR91 Wireless relay box (in cupboard...