plasterboard

I'll be plaster boarding my new extension next month. In another thread I posted on here, it seemed the general consensus was to batten rather than D&D. The walls are all flat and plumb and it does make it easier running conduit and pipework behind. I have since been very lucky to secure about...

Hi all, We are currently week 7 into our garage conversion and the doors and windows have just been installed and plasterboard and plaster now completed by our builders. Whilst we were painting the room, we noticed the plasterboard and plaster actually goes over the door/window frames which I’ve...

Hi everyone. I am trying to fit a tv to the wall and would very much appreciate some help. Upon getting a tv bracket and drilling into what i thought was a solid wall diving our living room and bedroom, the wall isnt a solid wall after all. I have 60mm of some material that is soft, plasteboard...

I have a house that I have been renting out to sharer's. One of the rooms is 6.32 m2. Too small to be rented out by 0.2m2. I was hoping that replacing the plasterboard with a thinner plasterboard might do the trick, but honestly, there is still not much space. It was already optimally used. Can...

I am replacing plasterboard round a UPVC window. I have already added expanding foam round the window frame to close up any gaps. But I also want to close up the cavity round the window, am I safe to use a small amount of expanding foam for this?

Hi all, won't be long before I'm plasterboarding my new extension. I was just looking for a few suggestions on the best alternatives to 'dot n dab'. The boards will be going on new blockwork (typical block/insulation/external brickwork). I don't want to use dot n dab. I know its tried and...

...

...

Hey Everyone, So I have skimmed plasterboard before and can do that pretty well. But I had a partition put up and that was boarded and skimmed. I have had to rip a section out this weekend as I wanted to lay some pipework into the wall. As you can see from the attached picture I just ripped...

Evening, I am stripping and recreating my bathroom as my disabled daughter needs a walk-in-shower with supports, rather than just the over-the-bath shower we have at the moment. The bathroom is VERY small, so space is everything. I have stripped back all the tiles, plaster and render back to...

So I just had a new chipboard floor glued and screwed in after adding noggins and levelling the joists. There are gaps between the edge of the chipboard and the blockwork, up to 15mm. There is a gap between the dot and dab wall and the new floor of up to 40mm high amd 30mm deep and also the void...

I have to sort out a detail which seem very tricky. I have ceiling with multifinish which stops at the stair opening and then I have the stair opening itslef which need to be wrapped up with MDF to have a strong edge whcih carry over to the above flooring. I would like to have a seamless on...

Hi all, I just wanted to check with people more experienced than I that I've not missed anything major with this job of levelling out this wall. Myself and my partner are due to complete on this house soon and in the master bedroom, there is a jut where built-in wardrobes used to be...

So we've had the hall and landing taken back to brick as the original lime plaster had blown and cracked badly in corners or was hole sounding and was coated with a Chrysotile artex skim that was damaged in places. We had a professional asbestos company do this work a few days ago, who fully...

Hi, apologies if this is the wrong section. I'm in a bit of a pickle, our shower has started leaking, a lot, and it looks like there had been a small leak for a while that soaked through the grout (or round it) and destroyed the plasterboard behind it, this in turn allowed movement which made...

Hi, I have been slowly upgrading a converted loft in my victorian semi. A couple of years ago I replaced the insulation in the rafters with PIR board. 100mm in between the rafters, 25mm underneath the rafter. 50mm gap between insulation in the rafters and batten for ventilation. At the...

Hi, I'm looking to install a heavy (about 4kg) light to replace some old ones in our living room. The original one was just mounted on the plasterboard. I'm not confident that this will support the light, so want to mount it into the beam above the plasterboard ceiling. This is however 85mm...

Have a good amount of damp proof membrane left which my builder previously used when laying down concrete. Really heavy duty stuff this: https://www.screwfix.com/p/capital-valley-plastics-ltd-damp-proof-membrane-blue-1200ga-15-x-4m/98181# I'm fixing insulated plasterboards with built in vapour...

Hi folks, Bear with me as I try to describe this as best as I can, pictures paint a thousand words though so please see those too! In a relatively new build (5yrs old, housebuilder was junk, lots of issues) and it's time to tackle the gaps appearing between the wooden 'large' skirting that...

I do seem to like making life hard for myself! What screw spacing do I need for this sheet of plasterboard: - In general? - Around the cutouts? I know I'll put thousands in if I don't ask advice first! Many thanks, Stephen