- Joined
- 19 Jul 2007
- Messages
- 5,942
- Reaction score
- 1,140
- Country
Have you actually checked the oil pressure
Recommendations for New Oil Burner - Equivalent to Riello G2SX (419T55)
- Thread starter polygraph
- Start date
-
- Tags
- no ignition oil burner riello
- Joined
- 5 Nov 2023
- Messages
- 20
- Reaction score
- 1
- Country
I've not considered anything other than the electrical side of the ignition process so far as I've mostly stuck to Riello's fault finding logic.
I don't have a suitable gauge to test the pressure sadly, but shouldn't the burner go to lock out if pressure is insufficient resulting in no flame or intermittent firing?
- Joined
- 19 Jul 2007
- Messages
- 5,942
- Reaction score
- 1,140
- Country
There could be a very small flame producing little heat but enough light to fool the photo cell.
I have seen this only a few times in 40 years........Usually caused by water contamination of the Kero
I have seen this only a few times in 40 years........Usually caused by water contamination of the Kero
- Joined
- 5 Nov 2023
- Messages
- 20
- Reaction score
- 1
- Country
Happy New Year and apologies for the radio silence last month.
I fitted the new burner a couple of weeks ago and so far so good
It was factory fitted with a 0.60 GPH 80 degrees H nozzle which is correct for my type of boiler, as was the 8 bar pump pressure and air damper adjustment setting. If I stick with this unit I'll get someone qualified in to analyse the gases and make any further adjustments necessary.
The Riello G5X appears to be identical to my old G3 with the exception that the fan unit is noticeably bigger. This means I'm no longer able to secure the metal cover which would normally close everything in. I'm not too concerned about this as the unit's in a cupboard - I might be less keen if it was in my kitchen.
I decided to re-use the old flange as I noticed it had a slightly angled mounting face to achieve the recommended lean. It also had a better way (in my opinion) of retaining the new gasket as the edges of the flange were raised to accept it. The old gasket is what I believe to be a type of asbestos. It resembled very thick plastic, had warped in places and was no longer sealing.
Inside the combustion chamber I was able to extract around 1kg of rust and combustion debris. I think the boiler's likely to have had next to no servicing in quite a few years. The old burner wasn't as badly corroded as I was expecting, although the nozzle has clearly seen better days.
I had to get a new green flexible fuel supply line as the one fitted was a hydraulic hose of the correct 1//4" thread but without the normal male stub, so whoever fitted it had sealed it with a massive wrap of PTFE tape. I'm surprised it hasn't leaked.
It's not an immediate priority, but I will try my best to get the old unit operational and will report back if I can ever get to the bottom of what the issue was.
Thanks for everyone's help in getting my heating back up and running.
polygraph.
I fitted the new burner a couple of weeks ago and so far so good
It was factory fitted with a 0.60 GPH 80 degrees H nozzle which is correct for my type of boiler, as was the 8 bar pump pressure and air damper adjustment setting. If I stick with this unit I'll get someone qualified in to analyse the gases and make any further adjustments necessary.
The Riello G5X appears to be identical to my old G3 with the exception that the fan unit is noticeably bigger. This means I'm no longer able to secure the metal cover which would normally close everything in. I'm not too concerned about this as the unit's in a cupboard - I might be less keen if it was in my kitchen.
I decided to re-use the old flange as I noticed it had a slightly angled mounting face to achieve the recommended lean. It also had a better way (in my opinion) of retaining the new gasket as the edges of the flange were raised to accept it. The old gasket is what I believe to be a type of asbestos. It resembled very thick plastic, had warped in places and was no longer sealing.
Inside the combustion chamber I was able to extract around 1kg of rust and combustion debris. I think the boiler's likely to have had next to no servicing in quite a few years. The old burner wasn't as badly corroded as I was expecting, although the nozzle has clearly seen better days.
I had to get a new green flexible fuel supply line as the one fitted was a hydraulic hose of the correct 1//4" thread but without the normal male stub, so whoever fitted it had sealed it with a massive wrap of PTFE tape. I'm surprised it hasn't leaked.
It's not an immediate priority, but I will try my best to get the old unit operational and will report back if I can ever get to the bottom of what the issue was.
Thanks for everyone's help in getting my heating back up and running.
polygraph.
The Riello G5X must be one of the best oil burners ever made, mine, including the 20kw Firebird SE boiler, will be 19 years old next May and has never tripped on combustion failure, my daughter's 18 year old, same boiler & burner, locked out only once in 18 years due to tank running dry.